Standards revision watch

Is your procedure calling out the current revision? Search below for the revision on file for each document. TRACE's Code Watch checks publishers' sites every week, and a person confirms each change before it shows here. Last weekly check: October 26, 2026.

SearchPublisher

175 of 175 documents

AMS 2175
Castings, Classification and Inspection of
SAE International · Current revision on file: SAE AMS2175B : 2024
Classification and inspection of castings: casting classes and grades, and the frequency and acceptance standards for radiographic, penetrant and magnetic particle inspection of each.
AMS 2431
Peening Media, General Requirements
SAE International · Current revision on file: SAE AMS2431E : 2023
General requirements for peening media (shot) used in shot peening.
AMS 2460
Plating, Chromium
SAE International · Current revision on file: SAE AMS2460B : 2023
Chromium plating: engineering process requirements, including embrittlement relief and inspection.
AMS 2644
Inspection Material, Penetrant
SAE International · Current revision on file: SAE AMS2644J : 2024
Inspection material, penetrant: the specification and qualification (QPL) basis for penetrant, emulsifier and developer materials used under ASTM E1417.
AMS 2658
Hardness and Conductivity Inspection of Aluminum Alloy Parts
SAE International · Current revision on file: SAE AMS2658E : 2026
Hardness and electrical conductivity inspection of wrought aluminum alloy parts to verify heat-treat condition.
AMS 2980
Carbon Fiber Fabric and Epoxy Resin Wet Lay-Up Repair Material, Part 0: Introduction
SAE International · Current revision on file: SAE AMS2980B : 2014 (2021)
Carbon fiber fabric and epoxy resin wet lay-up repair material, Part 0 (introduction) of the series for composite repair.
AMS 3107
Primer, Adhesive, Corrosion-Inhibiting
SAE International · Current revision on file: SAE AMS3107A : 1991 (2022)
Primer, adhesive, corrosion-inhibiting, for use under structural adhesives.
AMS 3272
Cloth, Nylon, Polyurethane Coated, Thermally, Radio Frequency, or Ultrasonically Sealable
SAE International · Current revision on file: SAE AMS3272B : 2011
Cloth, nylon, polyurethane-coated, thermally, radio-frequency or ultrasonically sealable.
AMS 3284
Sealing Compound, Low Adhesion, for Removable Panels and Fuel Tank Inspection Plates
SAE International · Current revision on file: SAE AMS3284D : 2024
Sealing compound, low adhesion, for removable panels and fuel tank inspection plates.
AMS 3571
Resin, Polyether Urethane (EU) Casting
SAE International · Current revision on file: SAE AMS3571C : 2011
Polyether urethane (EU) casting resin.
AMS 3670
Polyamide-Imide Bar, Rod, and Shapes
SAE International · Current revision on file: SAE AMS3670C : 2021
Polyamide-imide bar, rod and shapes.
AMS 3779
Tape, Adhesive, Pressure-Sensitive, Thermal Radiation Resistant
SAE International · Current revision on file: SAE AMS3779B : 2016
Pressure-sensitive adhesive tape, thermal-radiation resistant.
AMS 3787
Thread, Para-Aramid
SAE International · Current revision on file: SAE AMS3787B : 2016
Para-aramid thread.
AMS 3793
Tape and Webbing, Textile, Para-Aramid, Intermediate Modulus
SAE International · Current revision on file: SAE AMS3793D : 2018
Para-aramid tape and webbing, intermediate modulus.
AMS 3797
Webbing, Nylon, Integral Locking Slots
SAE International · Current revision on file: SAE AMS3797C : 2015
Nylon webbing with integral locking slots.
AMS 3801
Cloth, Parachute - Meta-Aramid, Low Modulus
SAE International · Current revision on file: SAE AMS3801D : 2016
Meta-aramid, low-modulus parachute cloth.
AMS 3867
Boron Filament Tape, Epoxy-Resin-Impregnated
SAE International · Current revision on file: SAE AMS3867C : 2016
Epoxy-resin-impregnated boron filament tape.
AMS 3899
Carbon Fiber Tape and Sheet
SAE International · Current revision on file: SAE AMS3899C : 2016
Carbon fiber tape and sheet.
AMS 3909
Cloth, Aramid, Intermediate Modulus
SAE International · Current revision on file: SAE AMS3909B : 2022
Aramid cloth, intermediate modulus.
AMS 4920
Titanium Alloy, Forgings
SAE International · Current revision on file: SAE AMS4920H : 2025
Titanium alloy forgings (Ti-6Al-4V, annealed), including the ultrasonic and macrostructure inspection requirements for premium-quality forgings.
AMS 5675
Nickel Alloy, Corrosion and Heat Resistant, Welding Wire
SAE International · Current revision on file: SAE AMS5675K : 2026
Corrosion- and heat-resistant nickel alloy welding wire.
AMS 5964
Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire, 718, Consumable Electrode Remelted or Vacuum Induction Melted and Remelted
SAE International · Current revision on file: SAE AMS5964A : 2023
Nickel alloy 718 welding wire, consumable-electrode remelted or vacuum induction melted and remelted.
AMS 6414
Steel, Bars, Forgings, and Tubing
SAE International · Current revision on file: SAE AMS6414N : 2023
Low-alloy steel (4340) bars, forgings and tubing, vacuum arc or electroslag remelted, with magnetic particle and ultrasonic inspection requirements.
AMS 6470
Steel, Nitriding, Bars, Forgings, and Tubing
SAE International · Current revision on file: SAE AMS6470R : 2024
Nitriding steel bars, forgings and tubing (1.6Cr-0.35Mo-1.13Al), for parts to be nitrided.
AMS 6514
Steel, Maraging, Bars, Forgings, Tubing, and Rings
SAE International · Current revision on file: SAE AMS6514L : 2026
Maraging steel (18Ni-250) bars, forgings, tubing and rings, consumable electrode melted.
AMS 6515
Steel, Maraging, Bars, Forgings, Tubing, and Rings
SAE International · Current revision on file: SAE AMS6515C : 2023
Maraging steel (18Ni-300) bars, forgings, tubing and rings, consumable electrode melted.
AMS-STD-2154
Inspection, Ultrasonic, Wrought Metals, Process For
SAE International · Current revision on file: SAE AMSSTD2154 Rev E · Last confirmed by hand 2026-08-31
Process for ultrasonic inspection of wrought metals (bar, billet, plate, forgings) with acceptance classes; the SAE-maintained successor to MIL-STD-2154 and still invoked on older drawings.
AMS-STD-2175Cancelled
Castings, Classification and Inspection of
SAE International · Current revision on file: SAE AMSSTD2175 Rev A · Superseded by AMS 2175 · Last confirmed by hand 2026-08-31
The SAE-maintained successor to MIL-STD-2175 for casting classification and inspection. Cancelled in 2004 and replaced by AMS 2175; listed so a procedure that still cites it can be traced forward.
AMS-STD-753Stabilized
Corrosion-Resistant Steel Parts
SAE International · Current revision on file: SAE AMSSTD753 Rev B · Last confirmed by hand 2026-08-31
Corrosion-resistant steel parts: sampling, inspection and testing for surface passivation. Stabilized by SAE, so no further revisions are expected.
ANSI/ASNT CP-105
Topical Outlines for Qualification of Nondestructive Testing Personnel
ASNT · Current revision on file: ANSI/ASNT CP-105 : 2024
Topical outlines (bodies of knowledge) for training NDT personnel in each method and level. SNT-TC-1A and CP-189 point here for what a training course must cover.
ANSI/ASNT CP-189
Qualification and Certification of Nondestructive Testing Personnel
ASNT · Current revision on file: ANSI/ASNT CP-189 : 2024
ANSI standard setting minimum requirements for an employer's NDT personnel qualification and certification program. Stricter than SNT-TC-1A, and requires an ASNT NDT Level III certificate for Level III personnel.
ASME B16.5
Pipe Flanges and Flanged Fittings NPS Through NPS 24 Metric Inch Standard
ASME · Current revision on file: ASME B16.5 : 2025
Pipe flanges and flanged fittings NPS 1/2 through NPS 24: dimensions, pressure-temperature ratings, materials and marking.
ASME B16.9
Factory Made Wrought Buttwelding Fittings
ASME · Current revision on file: ASME B16.9 : 2024
Factory-made wrought buttwelding fittings: dimensions, tolerances, ratings and testing.
ASME B18.16.6
Prevailing Torque Locknuts Inch Series
ASME · Current revision on file: ASME B18.16.6:2017
Prevailing-torque locknuts, inch series: dimensions, mechanical properties and performance requirements.
ASME B30.10
Hooks
ASME · Current revision on file: ASME B30.10 : 2024
Safety standard for hooks used in lifting: construction, marking, inspection, testing and maintenance.
ASME B30.20
Below the Hook Lifting Devices
ASME · Current revision on file: ASME B30.20 : 2025
Safety standard for below-the-hook lifting devices: design, marking, inspection, testing and operation.
ASME B31.1
Power Piping
ASME · Current revision on file: ASME B31.1 : 2026
Power piping code for piping in electric power stations, industrial plants and heating systems, including the examination and NDE requirements for welds.
ASME B31.3
Process Piping
ASME · Current revision on file: ASME B31.3 : 2024
Process piping code for refineries, chemical plants and similar facilities, including the examination, NDE and acceptance criteria for welds.
ASME B31.4
Pipeline Transportation Systems for Liquids and Slurries
ASME · Current revision on file: ASME B31.4 : 2025
Pipeline transportation systems for liquids and slurries: design, construction, inspection, testing and operation.
ASME B31.8
Gas Transmission and Distribution Piping Systems
ASME · Current revision on file: ASME B31.8 : 2025
Gas transmission and distribution piping systems: design, construction, inspection, testing and operation.
ASME B31.9
Building Services Piping
ASME · Current revision on file: ASME B31.9 : 2025
Building services piping code for lower-pressure heating, ventilating, air-conditioning and similar piping.
ASME BPVC Section IX
Welding, Brazing, and Fusing Qualifications
ASME · Current revision on file: BPVC.IX - 2025
Boiler and Pressure Vessel Code Section IX: qualification of welding, brazing and fusing procedures and of the personnel who perform them.
ASME BPVC Section V
Nondestructive Examination (Boiler and Pressure Vessel Code)
ASME · Current revision on file: BPVC.V - 2025
Boiler and Pressure Vessel Code Section V, Nondestructive Examination: the NDE method articles (RT, UT, MT, PT, ET, VT, leak, AE) invoked by the construction codes and B31.
ASME BPVC Section VIII Div 1
Rules for Construction of Pressure Vessels, Division 1
ASME · Current revision on file: BPVC.VIII.1 - 2025
Boiler and Pressure Vessel Code Section VIII Division 1: rules for construction of pressure vessels, including joint efficiency, examination and NDE requirements.
ASME NQA-1
Quality Assurance Requirements for Nuclear Facility Applications
ASME · Current revision on file: ASME NQA-1 : 2026
Quality assurance requirements for nuclear facility applications: the QA program standard invoked by nuclear owners and their suppliers.
ASNT SNT-TC-1A
Personnel Qualification and Certification in Nondestructive Testing
ASNT · Current revision on file: ASNT SNT-TC-1A : 2024
ASNT's recommended practice for employer-based qualification and certification of NDT personnel: the training, experience, examination and written-practice framework most industrial NDT programs are built on.
ASTM A275
Standard Practice for Magnetic Particle Examination of Steel Forgings
ASTM International · Current revision on file: ASTM A275/A275M-23
Practice for magnetic particle examination of steel forgings, covering technique, magnetising methods and evaluation; acceptance criteria come from the purchase order.
ASTM A388
Standard Practice for Ultrasonic Examination of Steel Forgings
ASTM International · Current revision on file: ASTM A388/A388M-26
Practice for ultrasonic examination of heavy steel forgings by straight and angle beam, including calibration, scanning coverage and recording of indications.
ASTM A435
Standard Specification for Straight Beam Ultrasonic Examination of Steel Plates
ASTM International · Current revision on file: ASTM A435/A435M-17(2023)
Specification for straight-beam ultrasonic examination of steel plates to detect gross internal laminations, with a grid-scan pattern and rejection criteria.
ASTM A578
Standard Specification for Straight Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
ASTM International · Current revision on file: ASTM A578/A578M-17(2023)
Specification for straight-beam ultrasonic examination of rolled steel plates for special applications, with acceptance levels A, B and C selected by the purchaser.
ASTM E1000
Standard Guide for Radioscopy
ASTM International · Current revision on file: ASTM E1000-24
Guide to radioscopy (real-time radiography): equipment, image quality, technique variables and system qualification.
ASTM E1004
Standard Test Method for Determining Electrical Conductivity using the Electromagnetic Eddy Current Method
ASTM International · Current revision on file: ASTM E1004-23
Test method for measuring electrical conductivity of nonferrous metals by eddy current, used to verify alloy and heat-treat condition of aluminum parts.
ASTM E1025
Standard Practice for Design Manufacture and Material Grouping Classification of Hole Type Image Quality Indicators Iqi Used for Radiology
ASTM International · Current revision on file: ASTM E1025-18(2025)
Practice for the design, manufacture and material grouping of hole-type image quality indicators (IQIs) used in radiography.
ASTM E1030
Standard Practice for Radiographic Examination of Metallic Castings
ASTM International · Current revision on file: ASTM E1030/E1030M-21
Practice for radiographic examination of metallic castings with film, including technique, IQI selection and film quality requirements.
ASTM E1032
Standard Practice for Radiographic Examination of Weldments using Industrial X Ray Film
ASTM International · Current revision on file: ASTM E1032-25
Practice for radiographic examination of weldments using industrial X-ray film: technique, geometry, IQI placement and film quality.
ASTM E1065
Standard Practice for Evaluating Characteristics of Ultrasonic Search Units
ASTM International · Current revision on file: ASTM E1065/E1065M-20(2025)
Practice for evaluating the characteristics of ultrasonic search units (transducers), including frequency, bandwidth and beam profile measurements.
ASTM E1135
Standard Test Method for Comparing the Brightness of Fluorescent Penetrants
ASTM International · Current revision on file: ASTM E1135-19(2024)
Test method for comparing the brightness of fluorescent penetrants, used to qualify penetrant materials and check in-use penetrant against a reference sample.
ASTM E114
Standard Practice for Ultrasonic Pulse Echo Straight Beam Contact Testing
ASTM International · Current revision on file: ASTM E114-20
Practice for ultrasonic pulse-echo straight-beam contact testing, covering equipment, reference standards and the basic technique other UT standards build on.
ASTM E1161
Standard Practice for Radiologic Examination of Semiconductors and Electronic Components
ASTM International · Current revision on file: ASTM E1161-21
Practice for radiologic examination of semiconductors and electronic components.
ASTM E1165
Standard Test Method for Measurement of Focal Spots of Industrial X Ray Tubes by Pinhole Imaging
ASTM International · Current revision on file: ASTM E1165-20
Test method for measuring the focal spot of industrial X-ray tubes by pinhole imaging, a factor in radiographic geometric unsharpness.
ASTM E1213
Standard Practice for Minimum Resolvable Temperature Difference for Thermal Imaging Systems
ASTM International · Current revision on file: ASTM E1213-14(2022)
Practice for measuring the minimum resolvable temperature difference of thermal imaging systems.
ASTM E1255
Standard Practice for Radioscopy
ASTM International · Current revision on file: ASTM E1255-23
Practice for radioscopy, defining system performance, technique and qualification requirements for real-time radiographic examination.
ASTM E127
Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks
ASTM International · Current revision on file: ASTM E127-20
Practice for fabricating and controlling aluminum alloy flat-bottom-hole ultrasonic reference blocks, the standard reference blocks for immersion UT of wrought products.
ASTM E1311
Standard Practice for Minimum Detectable Temperature Difference for Thermal Imaging Systems
ASTM International · Current revision on file: ASTM E1311-14(2022)
Practice for measuring the minimum detectable temperature difference of thermal imaging systems.
ASTM E1316
Standard Terminology for Nondestructive Examinations
ASTM International · Current revision on file: ASTM E1316-26c
Standard terminology for nondestructive examinations: the definitions used across ASTM's NDT standards, arranged by method.
ASTM E1320
Standard Reference Radiographs for Titanium Castings
ASTM International · Current revision on file: ASTM E1320-20(2026)
Reference radiographs for titanium castings, used to grade discontinuities by type and severity.
ASTM E1324
Standard Guide for Measuring Some Electronic Characteristics of Ultrasonic Testing Instruments
ASTM International · Current revision on file: ASTM E1324-21(2026)
Guide for measuring the electronic characteristics of ultrasonic testing instruments, such as linearity, gain accuracy and pulser performance.
ASTM E1390
Standard Specification for Illuminators Used for Viewing Industrial Radiographs
ASTM International · Current revision on file: ASTM E1390-21
Specification for illuminators (viewers) used to view industrial radiographs, including luminance and variable-intensity requirements.
ASTM E1411
Standard Practice for Qualification of Radioscopic Systems
ASTM International · Current revision on file: ASTM E1411-23
Practice for qualification of radioscopic systems, establishing the performance a system must demonstrate before use.
ASTM E1416
Standard Practice for Radioscopic Examination of Weldments
ASTM International · Current revision on file: ASTM E1416-23
Practice for radioscopic examination of weldments.
ASTM E1417/E1417M
Liquid Penetrant Testing
ASTM International · Current revision on file: ASTM E1417/E1417M-21e1
Liquid penetrant testing process requirements for aerospace and other critical parts: material classification, process controls, personnel and equipment. The PT standard most aerospace drawings invoke.
ASTM E1441
Standard Guide for Computed Tomography Ct
ASTM International · Current revision on file: ASTM E1441-19(2026)
Guide to computed tomography (CT): principles, system characteristics and factors affecting image quality.
ASTM E1444/E1444M
Magnetic Particle Testing for Aerospace
ASTM International · Current revision on file: ASTM E1444/E1444M-26
Magnetic particle testing process requirements for aerospace and other critical parts: equipment, materials, technique, process controls and personnel. The MT standard most aerospace drawings invoke.
ASTM E1495
Standard Guide for Acousto Ultrasonic Assessment of Composites Laminates and Bonded Joints
ASTM International · Current revision on file: ASTM E1495/E1495M-17(2025)
Guide for acousto-ultrasonic assessment of composites, laminates and bonded joints.
ASTM E1543
Standard Practice for Noise Equivalent Temperature Difference of Thermal Imaging Systems
ASTM International · Current revision on file: ASTM E1543-14(2022)
Practice for measuring the noise-equivalent temperature difference of thermal imaging systems.
ASTM E155
Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings
ASTM International · Current revision on file: ASTM E155-20(2026)
Reference radiographs for inspection of aluminum and magnesium castings, used to grade discontinuities by type and severity.
ASTM E1570
Standard Practice for Fan Beam Computed Tomographic CT Examination
ASTM International · Current revision on file: ASTM E1570-19(2026)
Practice for fan-beam computed tomographic (CT) examination.
ASTM E1629
Standard Practice for Determining the Impedance of Absolute Eddy Current Probes Astm E1629 12
ASTM International · Current revision on file: ASTM E1629-12(2025)
Practice for determining the impedance of absolute eddy current probes.
ASTM E164
Standard Practice for Contact Ultrasonic Testing of Weldments
ASTM International · Current revision on file: ASTM E164-24
Practice for contact ultrasonic testing of weldments, covering angle-beam technique, calibration blocks and scanning of welds in plate and pipe.
ASTM E1647
Standard Practice for Determining Contrast Sensitivity in Radiology
ASTM International · Current revision on file: ASTM E1647-16(2022)
Practice for determining contrast sensitivity in radiology, using a contrast-sensitivity gauge.
ASTM E1648
Standard Reference Radiographs for Examination of Aluminum Fusion Welds
ASTM International · Current revision on file: ASTM E1648-20(2026)
Reference radiographs for examination of aluminum fusion welds.
ASTM E165/E165M
Liquid Penetrant Testing for General Industry
ASTM International · Current revision on file: ASTM E165/E165M-23
Practice for liquid penetrant testing for general industry: methods A through D, penetrant materials, process steps and interpretation.
ASTM E1672
Standard Guide for Computed Tomography CT System Selection
ASTM International · Current revision on file: ASTM E1672-12(2020)
Guide for selecting a computed tomography (CT) system.
ASTM E1695
Standard Test Method for Measurement of Computed Tomography CT System Performance
ASTM International · Current revision on file: ASTM E1695-20e1
Test method for measuring computed tomography (CT) system performance.
ASTM E1742/E1742M
Radiographic Examination
ASTM International · Current revision on file: ASTM E1742/E1742M-23
Practice for film radiographic examination of aerospace and other critical parts: technique, image quality, film processing and records. The RT standard most aerospace drawings invoke.
ASTM E1814
Standard Practice for Computed Tomographic CT Examination of Castings Astm E1814 14
ASTM International · Current revision on file: ASTM E1814-25
Practice for computed tomographic (CT) examination of castings.
ASTM E1815
Standard Test Method for Classification of Film Systems for Industrial Radiography
ASTM International · Current revision on file: ASTM E1815-18(2023)
Test method for classifying industrial radiographic film systems by speed, contrast and granularity.
ASTM E1817
Standard Practice for Controlling Quality of Radiological Examination by using Representative Quality Indicators RQIs Astm E1817 08
ASTM International · Current revision on file: ASTM E1817-26
Practice for controlling the quality of radiologic examination using representative quality indicators (RQIs).
ASTM E192
Standard Reference Radiographs of Investment Steel Castings for Aerospace Applications
ASTM International · Current revision on file: ASTM E192-20(2026)
Reference radiographs of investment steel castings for aerospace applications.
ASTM E213
Standard Practice for Ultrasonic Testing of Metal Pipe and Tubing
ASTM International · Current revision on file: ASTM E213-22
Practice for ultrasonic testing of metal pipe and tubing, using angle-beam techniques and notch reference standards.
ASTM E215
Standard Practice for Standardizing Equipment and Electromagnetic Examination of Seamless Aluminum Alloy Tube
ASTM International · Current revision on file: ASTM E215-22
Practice for standardising equipment for electromagnetic (eddy current) examination of seamless aluminum alloy tube.
ASTM E2375
Ultrasonic Testing of Wrought Products
ASTM International · Current revision on file: ASTM E2375-26a
Practice for ultrasonic testing of wrought products (bar, billet, plate, forgings) by straight and angle beam, with acceptance classes. The successor to MIL-STD-2154 for most aerospace users.
ASTM E242
Standard Reference Radiographs for Appearances of Radiographic Images As Certain Parameters Are Changed Astm E242 15
ASTM International · Current revision on file: ASTM E242-15(2026)
Reference radiographs showing how radiographic images change as exposure parameters change.
ASTM E243
Standard Practice for Electromagnetic Eddy Current Examination of Copper and Copper Alloy Tubes
ASTM International · Current revision on file: ASTM E243-24
Practice for electromagnetic (eddy current) examination of copper and copper-alloy tubes.
ASTM E2533
Standard Guide for Nondestructive Testing of Polymer Matrix Composites Used in Aerospace Applications
ASTM International · Current revision on file: ASTM E2533-21
Guide to nondestructive testing of polymer matrix composites used in aerospace applications, surveying the applicable methods.
ASTM E2580
Standard Practice for Ultrasonic Testing of Flat Panel Composites and Sandwich Core Materials Used in Aerospace Applications
ASTM International · Current revision on file: ASTM E2580-24
Practice for ultrasonic testing of flat panel composites and sandwich core materials used in aerospace applications.
ASTM E272
Standard Reference Radiographs for High Strength Copper Base and Nickel Copper Alloy Castings
ASTM International · Current revision on file: ASTM E272-21
Reference radiographs for high-strength copper-base and nickel-copper alloy castings.
ASTM E3022
Standard Practice for Measurement of Emission Characteristics and Requirements for LED UV A Lamps Used in Fluorescent Penetrant and Magnetic Particle Testing
ASTM International · Current revision on file: ASTM E3022-26a
Practice for measuring the emission characteristics of, and requirements for, LED UV-A lamps used in fluorescent penetrant and magnetic particle testing.
ASTM E3024
Standard Practice for Magnetic Particle Testing for General Industry
ASTM International · Current revision on file: ASTM E3024/E3024M-22a
Practice for magnetic particle testing for general industry: equipment, materials, technique and process controls outside the aerospace scope of E1444.
ASTM E317
Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments
ASTM International · Current revision on file: ASTM E317-21
Practice for evaluating the performance characteristics of ultrasonic pulse-echo instruments and systems without the use of electronic measurement instruments.
ASTM E376
Standard Practice for Measuring Coating Thickness by Magnetic Field or Eddy Current Electromagnetic Testing Methods
ASTM International · Current revision on file: ASTM E376-26
Practice for measuring coating thickness by magnetic-field or eddy current (electromagnetic) methods.
ASTM E390
Standard Reference Radiographs for Steel Fusion Welds
ASTM International · Current revision on file: ASTM E390-20(2026)
Reference radiographs for steel fusion welds, used to grade weld discontinuities by type and severity.
ASTM E426
Standard Practice for Electromagnetic Eddy Current Examination of Seamless and Welded Tubular Products Titanium Austenitic Stainless Steel and Similar Alloys
ASTM International · Current revision on file: ASTM E426-16(2021)
Practice for electromagnetic (eddy current) examination of seamless and welded tubular products of titanium, austenitic stainless steel and similar alloys.
ASTM E431
Standard Guide to Interpretation of Radiographs of Semiconductors and Related Devices
ASTM International · Current revision on file: ASTM E431-96(2022)
Guide to interpretation of radiographs of semiconductors and related devices.
ASTM E446
Standard Reference Radiographs for Steel Castings Up to 2 in 50 8 Mm in Thickness
ASTM International · Current revision on file: ASTM E446-20(2026)
Reference radiographs for steel castings up to 2 in. (50.8 mm) in thickness.
ASTM E494
Standard Practice for Measuring Ultrasonic Velocity in Materials by Comparative Pulse Echo Method
ASTM International · Current revision on file: ASTM E494-20(2025)
Practice for measuring ultrasonic velocity in materials by the comparative pulse-echo method.
ASTM E543
Standard Specification for Agencies Performing Nondestructive Testing
ASTM International · Current revision on file: ASTM E543-26
Specification for agencies performing nondestructive testing: the quality system, personnel, equipment and procedure requirements a purchaser can use to evaluate an NDT service provider.
ASTM E566
Standard Practice for Electromagnetic Eddy Current Magnetic Induction Sorting of Ferrous Metals
ASTM International · Current revision on file: ASTM E566-24
Practice for electromagnetic (eddy current, magnetic induction) sorting of ferrous metals by alloy, hardness or heat-treat condition.
ASTM E587
Standard Practice for Ultrasonic Angle Beam Contact Testing Astm E587 15
ASTM International · Current revision on file: ASTM E587-15(2025)
Practice for ultrasonic angle-beam contact testing, covering equipment, reference standards and technique.
ASTM E709
Guide for Magnetic Particle Testing
ASTM International · Current revision on file: ASTM E709-21
Guide for magnetic particle testing: the reference on MT principles, equipment, magnetising techniques, materials and interpretation.
ASTM E747
Standard Practice for Design Manufacture and Material Grouping Classification of Wire Image Quality Indicators Iqi Used for Radiology
ASTM International · Current revision on file: ASTM E747-24
Practice for the design, manufacture and material grouping of wire image quality indicators (IQIs) used in radiography.
ASTM E797
Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse Echo Contact Method
ASTM International · Current revision on file: ASTM E797/E797M-21
Practice for measuring thickness by the manual ultrasonic pulse-echo contact method.
ASTM E801
Standard Practice for Controlling Quality of Radiographic Examination of Electronic Devices
ASTM International · Current revision on file: ASTM E801-21
Practice for controlling the quality of radiographic examination of electronic devices.
ASTM E94
Standard Guide for Radiographic Examination using Industrial Radiographic Film
ASTM International · Current revision on file: ASTM E94/E94M-22
Guide for radiographic examination using industrial radiographic film: technique selection, image quality, IQIs, film processing and records.
AWS A1.1
Metric Practice Guide for the Welding Industry
American Welding Society · Current revision on file: A1.1:2026
Metric practice guide for the welding industry.
AWS A2.4
Standard Symbols for Welding, Brazing, and Nondestructive Examination
American Welding Society · Current revision on file: A2.4:2020
Standard symbols for welding, brazing and nondestructive examination: how welds and required examinations are called out on drawings.
AWS A3.0
Standard Welding Terms and Definitions
American Welding Society · Current revision on file: A3.0:2025
Standard welding terms and definitions, including those for brazing, soldering, thermal cutting and thermal spraying.
AWS A5.1
Specification for Carbon Steel Electrodes for Shielded Metal Arc Welding
American Welding Society · Current revision on file: A5.1/A5.1M:2025
Specification for carbon steel electrodes for shielded metal arc welding (SMAW).
AWS A5.10
Specification for Bare Aluminum and Aluminum-Alloy Welding Electrodes and Rods
American Welding Society · Current revision on file: A5.10/A5.10M:2023
Specification for bare aluminum and aluminum-alloy welding electrodes and rods.
AWS A5.11
Specification for Nickel and Nickel-Alloy Welding Electrodes for Shielded Metal Arc Welding
American Welding Society · Current revision on file: A5.11/A5.11M:2025
Specification for nickel and nickel-alloy welding electrodes for shielded metal arc welding.
AWS A5.12
Specification for Tungsten and Oxide Dispersed Tungsten Electrodes for Arc Welding and Cutting
American Welding Society · Current revision on file: A5.12:2024
Specification for tungsten and oxide-dispersed tungsten electrodes for arc welding and cutting.
AWS A5.14
Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods
American Welding Society · Current revision on file: A5.14/A5.14M:2026
Specification for nickel and nickel-alloy bare welding electrodes and rods.
AWS A5.18
Specification for Carbon Steel Electrodes and Rods for Gas Shielded Arc Welding
American Welding Society · Current revision on file: A5.18/A5.18M:2025
Specification for carbon steel electrodes and rods for gas shielded arc welding (GMAW and GTAW).
AWS A5.22
Specification for Stainless Steel Flux Cored and Metal Cored Welding Electrodes and Rods
American Welding Society · Current revision on file: A5.22/A5.22M:2024
Specification for stainless steel flux cored and metal cored welding electrodes and rods.
AWS A5.29
Specification for Low-Alloy Steel Electrodes for Flux Cored Arc Welding
American Welding Society · Current revision on file: A5.29/A5.29M:2026
Specification for low-alloy steel electrodes for flux cored arc welding.
AWS A5.32
Specification for Welding Shielding Gases
American Welding Society · Current revision on file: A5.32:2021 · Last confirmed by hand 2026-09-07
Specification for welding shielding gases: composition, purity and classification.
AWS A5.4
Specification for Stainless Steel Electrodes for Shielded Metal Arc Welding
American Welding Society · Current revision on file: A5.4/A5.4M:2012
Specification for stainless steel electrodes for shielded metal arc welding.
AWS A5.5
Specification for Low-Alloy Steel Electrodes for Shielded Metal Arc Welding
American Welding Society · Current revision on file: A5.5/A5.5M:2022
Specification for low-alloy steel electrodes for shielded metal arc welding.
AWS A5.9
Specification for Bare Stainless Steel Welding Electrodes and Rods
American Welding Society · Current revision on file: A5.9/A5.9M:2022
Specification for bare stainless steel welding electrodes and rods.
AWS B1.10
Guide for the Nondestructive Examination of Welds
American Welding Society · Current revision on file: B1.10:2016
Guide for the nondestructive examination of welds: which methods find which discontinuities, and their limitations.
AWS B1.11
Guide for the Visual Examination of Welds
American Welding Society · Current revision on file: B1.11:2015
Guide for the visual examination of welds, including the discontinuities visual inspection can and cannot find.
AWS B2.1
Specification for Welding Procedure and Performance Qualification
American Welding Society · Current revision on file: B2.1/B2.1M:2026
Specification for welding procedure and performance qualification, the AWS counterpart to ASME Section IX.
AWS B4.0
Standard Methods for Mechanical Testing of Welds
American Welding Society · Current revision on file: B4.0:2007
Standard methods for mechanical testing of welds: tension, bend, hardness, impact and fracture tests.
AWS B5.15
Specification for the Qualification of Radiographic Interpreters
American Welding Society · Current revision on file: B5.15:2010
Specification for the qualification of radiographic interpreters.
AWS B5.17
Specification for the Qualification of Welding Fabricators
American Welding Society · Current revision on file: B5.17:2025-AMD1
Specification for the qualification of welding fabricators.
AWS B5.2
Specification for the Qualification of Welding Inspector Specialists and Welding Inspector Assistants
American Welding Society · Current revision on file: B5.2:2026
Specification for the qualification of welding inspector specialists and welding inspector assistants.
AWS B5.9
Specification for the Qualification of Welding Supervisors
American Welding Society · Current revision on file: B5.9:2006
Specification for the qualification of welding supervisors.
AWS C1.1
Recommended Practices for Resistance Welding
American Welding Society · Current revision on file: C1.1:2019-AMD1
Recommended practices for resistance welding.
AWS C3.2
Standard Method for Evaluating the Strength of Brazed Joints
American Welding Society · Current revision on file: C3.2:2019
Standard method for evaluating the strength of brazed joints.
AWS C3.4
Specification for Torch Brazing
American Welding Society · Current revision on file: C3.4:2026
Specification for torch brazing.
AWS C3.6
Specification for Furnace Brazing
American Welding Society · Current revision on file: C3.6:2026
Specification for furnace brazing.
AWS C3.7
Specification for Aluminum Brazing
American Welding Society · Current revision on file: C3.7:2011
Specification for aluminum brazing.
AWS D1.1
Structural Welding Code — Steel
American Welding Society · Current revision on file: D1.1/D1.1M:2025-AMD1
Structural welding code for steel: design, qualification, fabrication and inspection of welded steel structures, including NDT acceptance criteria.
AWS D1.2
Structural Welding Code — Aluminum
American Welding Society · Current revision on file: D1.2/D1.2M:2026
Structural welding code for aluminum.
AWS D1.3
Structural Welding Code — Sheet Steel
American Welding Society · Current revision on file: D1.3/D1.3M:2025
Structural welding code for sheet steel.
AWS D1.4
Structural Welding Code — Steel Reinforcing Bars
American Welding Society · Current revision on file: D1.4/D1.4M:2018-AMD1
Structural welding code for steel reinforcing bars.
AWS D1.5
Bridge Welding Code
American Welding Society · Current revision on file: D1.5:2025
Bridge welding code (AASHTO/AWS): fabrication and inspection of welded highway bridges.
AWS D1.6
Structural Welding Code — Stainless Steel
American Welding Society · Current revision on file: D1.6/D1.6M:2017
Structural welding code for stainless steel.
AWS D1.8
Structural Welding Code — Seismic Supplement
American Welding Society · Current revision on file: D1.8/D1.8M:2021
Seismic supplement to AWS D1.1: additional welding, filler metal, workmanship and inspection requirements for steel structures designed for seismic loading, used with the AISC seismic provisions.
AWS D10.11
Guide for Root Pass Welding of Pipe Without Backing
American Welding Society · Current revision on file: D10.11:2007
Guide for root pass welding of pipe without backing.
AWS D14.1
Specification for Welding of Industrial and Mill Cranes and Other Material Handling Equipment
American Welding Society · Current revision on file: D14.1/D14.1M:2005-AMD1
Specification for welding of industrial and mill cranes and other material handling equipment.
AWS D14.3
Specification for Welding Earthmoving, Construction, and Agricultural Equipment
American Welding Society · Current revision on file: D14.3/D14.3M:2019
Specification for welding earthmoving, construction and agricultural equipment.
AWS D14.5
Specification for Welding of Presses and Press Components
American Welding Society · Current revision on file: D14.5/D14.5M:2009
Specification for welding of presses and press components.
AWS D14.6
Specification for Welding of Rotating Elements of Equipment
American Welding Society · Current revision on file: D14.6/D14.6M:2024
Specification for welding of rotating elements of equipment.
AWS D15.1
Railroad Welding Specification for Cars and Locomotives
American Welding Society · Current revision on file: D15.1/D15.1M:2025
Railroad welding specification for cars and locomotives.
AWS D17.1
Specification for Fusion Welding for Aerospace Applications
American Welding Society · Current revision on file: D17.1/D17.1M:2024
Specification for fusion welding for aerospace applications, including NDT and acceptance criteria for aerospace welds.
AWS D9.1
Sheet Metal Welding Code
American Welding Society · Current revision on file: D9.1/D9.1M:2026
Sheet metal welding code.
AWS QC1
Specification for AWS Certification of Welding Inspectors
American Welding Society · Current revision on file: QC1:2016-AMD1
Specification for AWS certification of welding inspectors (CWI, SCWI and CAWI).
AWS QC15
Specification for the Certification of Radiographic Interpreters
American Welding Society · Current revision on file: QC15:2008-AMD1
Specification for the certification of radiographic interpreters.
ISO 17636-2
Non Destructive Testing of Welds Radiographic Testing Part 2 X and Gamma Ray Techniques with Digital Detectors
ISO · Current revision on file: ISO 17636-2:2022
Radiographic testing of fusion-welded joints using digital detectors (computed radiography and digital detector arrays), with technique classes and image quality requirements.
ISO 9001
Quality Management Systems Requirements
ISO · Current revision on file: ISO 9001:2026
Requirements for a quality management system: the basis for most supplier quality registrations and for the documented procedures an NDT program sits inside.
ISO 9712
Qualification and Certification of NDT Personnel
ISO · Current revision on file: ISO 9712:2021
International scheme for third-party qualification and certification of NDT personnel by an accredited certification body, rather than by the employer.
ISO/IEC 17025
General Requirements for the Competence of Testing and Calibration Laboratories
ISO · Current revision on file: ISO/IEC 17025:2017
Competence requirements for testing and calibration laboratories, including impartiality, method validation and measurement traceability. The basis for laboratory accreditation.
MIL-STD-1689
Fabrication, Welding, and Inspection of Ships Structure
NAVSEA · Current revision on file: Revision A 23-NOV-1990
Fabrication, welding and inspection requirements for the hull and structure of surface combatant ships: materials, weld joint design, workmanship, inspection and records. The surface-ship counterpart to T9074-AD-GIB-010/1688.
MIL-STD-1907
Inspection, Liquid Penetrant and Magnetic Particle, Soundness Requirements for Materials, Parts and Weldments
Department of Defense · Current revision on file: Notice 7 - Validation 11-MAR-2025
Acceptance (soundness) criteria for liquid penetrant and magnetic particle inspection: four PT quality levels and three MT quality levels, invoked on drawings for materials, parts and weldments. Army-prepared, used across the services.
MIL-STD-2035
Nondestructive Testing Acceptance Criteria
NAVSEA · Current revision on file: Revision A Notice 1 - Validation 09-MAR-2026
The Navy's NDT acceptance criteria: classes of acceptance for visual, radiographic, magnetic particle, liquid penetrant, ultrasonic and eddy current inspection of welds, castings and forgings, invoked by 278, 1688 and Navy drawings.
MIL-STD-2132
Nondestructive Examination Requirements for Special Applications
NAVSEA · Current revision on file: Revision F Notice 1 - Administrative 27-JUN-2022
NDE requirements for special (naval nuclear propulsion) applications, including personnel, procedure and equipment qualification. Distribution of the document itself is limited; its revision status is public.
MIL-STD-22
Welded Joint Design
NAVSEA · Current revision on file: Revision D Notice 3 - Validation 21-MAR-1991
The Navy's catalogue of welded joint designs (the P-, B-, C- and T-series joint numbers) for manual, semi-automatic and automatic arc and gas welding, invoked by S9074-AR-GIB-010/278 and the MIL-STD-278 fabrication documents.
MIL-STD-271Cancelled
Requirements for Nondestructive Testing Methods
NAVSEA · Current revision on file: MIL-STD-271F (cancelled 27 May 1998) · Superseded by NAVSEA T9074-AS-GIB-010/271 · Last confirmed by hand 2026-09-11
The original Navy NDT methods standard, cancelled in 1998 and replaced by NAVSEA T9074-AS-GIB-010/271. Listed so a procedure or purchase order that still cites MIL-STD-271 can be traced to its replacement.
NAS410
Certification and Qualification of Nondestructive Test Personnel
AIA · Current revision on file: Revision 6
Aerospace industry standard for certification and qualification of NDT personnel, maintained by AIA. The basis for most aerospace and Nadcap written practices, and harmonised with EN 4179.
NAVSEA S9074-AQ-GIB-010/248
Requirements for Welding and Brazing Procedure and Performance Qualification
NAVSEA · Current revision on file: Revision 1 (12 November 2019) · Last confirmed by hand 2026-09-11
Qualification of welding and brazing procedures, and of welders, welding operators and brazers, for Navy ship work. Successor to MIL-STD-248.
NAVSEA S9074-AR-GIB-010/278
Requirements for Fabrication Welding and Inspection, and Casting Inspection and Repair for Machinery, Piping, and Pressure Vessels
NAVSEA · Current revision on file: Original issue (1 August 1995) · Last confirmed by hand 2026-09-11
Fabrication welding, inspection, and casting inspection and repair requirements for machinery, piping and pressure vessels in Navy ships, including which NDT each class of joint gets. Successor to MIL-STD-278.
NAVSEA T9074-AD-GIB-010/1688
Requirements for Fabrication, Welding, and Inspection of Submarine Structure
NAVSEA · Current revision on file: Revision 1 (13 July 2012) · Last confirmed by hand 2026-09-11
Fabrication, welding and inspection requirements for submarine and submersible structure, including HY-80/100 hull welds, inspection acceptance standards and record requirements. Successor to MIL-STD-1681 and MIL-STD-1688.
NAVSEA T9074-AS-GIB-010/271
Requirements for Nondestructive Testing Methods
NAVSEA · Current revision on file: Revision 1 (11 September 2014) · Last confirmed by hand 2026-09-11
The Navy's NDT methods document: procedure, personnel and equipment qualification requirements for radiographic, magnetic particle, liquid penetrant, ultrasonic, eddy current and visual testing on ship construction and repair. Successor to MIL-STD-271.
NAVSEA T9074-BD-GIB-010/0300
Base Materials for Critical Applications: Requirements for Low Alloy Steel Plate, Forgings, Castings, Shapes, Bars, and Heads of HY-80/100/130 and HSLA-80/100
NAVSEA · Current revision on file: Revision 2 (18 December 2012) · Last confirmed by hand 2026-09-11
Material, testing and inspection requirements for HY-80/100/130 and HSLA-80/100 steel plate, forgings, castings and shapes used in critical Navy structure.

Where these figures come from

Revisions come from TRACE's Code Watch list, read straight from its public export.
Confirm with the publisher, and with what your customer's contract or purchase order calls out, before you change a procedure. Contracts often name a specific revision on purpose.
Not affiliated with or endorsed by any of the publishers named.

Standards revision watch

Where these figures come from

More for NDT people